1.
A common method of cooking ripe plantain for sale is
boiling.
roasting.
grilling.
baking.
2.
To shorten the cooking time for meat,
slice along the grain.
cut into small pieces.
slice into thin pieces.
cut across the grain.
3.
In taking body measurement, a firm tape measure is needed to
save time.
avoid wasting fabric.
obtain accuracy.
make sewing easy.
4.
Which of the following principles of design is similar to proportion?
Balance
Perspective
Rhythm
Scale
5.
A preliminary design is meant to
improve creativity.
increase production.
make sketches.
produce ideas.
6.
Use the sketch in Figure 1 to answer the question below
Which of the following represents the front view in the direction of arrow Z?
7.
Use the sketch in Figure 1 to answer the question below
Which of the following represent the left end elevation?
8.
A single unit of a design is known as
motif.
pattern.
plan.
print.
9.
Angles are measured by using a
compass.
protractor.
rule.
set square.
10.
In designing, the analysis question, what is the purpose of the unit? falls under
construction.
ergonomics.
function.
material.
11.
To repair an electrical fault, a safety precaution to observe is to
disconnect live wires.
remove fuse.
remove cover of socket.
switch off main supply.
12.
Which of the following is not a cause of weakness in furniture?
Loose joint
Insufficient polish
Overloading
Removal of nail
13.
The tee-square is used for drawing
arcs.
circles.
horizontal lines.
vertical lines.
14.
Identify the type of lettering used for emphasis.
Freestyle
Gothic
Italics
Romans
15.
Strips cut on the true cross of fabric are usually used for curved edges because they
stretch easily.
do not fray.
are easily prepared.
are colourful.
16.
The body of a box-iron is made from
aluminium.
cast iron.
copper.
wrought iron.
17.
Polyvinyl acetate is a type of
abrasive.
adhesive.
aggregate.
finish.
18.
The type of aggregate that passes through a 5 mm wire mesh is
clay.
laterite.
sand.
stone.
19.
Which of the following tools is suitable for pairing in wood?
Cross-cut saw
Firmer chisel
Mortise chisel
Rip saw
20.
Use the sketch in Figure 2 to answer the question below
The tool is used for
cutting bricks.
mixing mortar.
picking and spreading mortar.
setting out a wall.
21.
Use the sketch in Figure 2 to answer the question below
The part labelled T is
blade.
ferrule.
handle.
shank.
22.
Personal safety is observed on site in order to
reduce the risk of damaging tools.
prevent damage to workpiece.
care and maintain tools.
prevent accidents to workers.
23.
Use the sketch in Figure 3 to answer the question below
The sketch shown is
gauge box.
head pan.
mould box.
pallet.
24.
Use the sketch in Figure 3 to answer the question below
The tool is used for
holding blocks.
moulding blocks.
fetching water.
batching materials.
25.
Use the sketch in Figure 4 to answer the question below
Which of the following represents the front view in the direction of arrow Z?
26.
Use the sketch in Figure 4 to answer the question below
Which of the following represent the left end elevation?
27.
The sketch shows the process of
plumbing a wall.
levelling a wall.
spreading mortar for a wall.
checking height of a wall.
28.
The tool labelled K is the
builder’s square.
gauge rod.
spirit level.
straight edge.
29.
In an electrical circuit, the fuse is connected to the
earth wire.
live wire.
negative wire.
neutral wire.
30.
Which of the following components helps to open and close a circuit?
Cell
Fuse
Plug
Switch
a)
What is temporary stitches?
b)
State two reasons for setting a table for family meals.
c)
A unit for hanging school uniforms is to be designed and made in the school workshop.
i)
State two places where the unit would be placed in the workshop.
ii)
State two specifications of the unit based on construction;
ii)
Name one specific material to be used for making the unit.
d)
i)
List five important pieces of information printed onto a package.
ii)
Name two other methods for making a print.
a)
i)
Make a freehand pictorial sketch of the hand file with a handle used for filing metals.
ii)
Label any two parts of the hand file sketched in question (a)(i).
iii)
State one use of the hand file.
b)
Copy and complete the table below:
| S/N | OPERATION | TWO TOOLS REQUIRED FOR EACH OPERATION |
| I | Moulding of bricks | |
| II | Marking out on metal plate | |
| III | Soldering sheet metals | |
| IV | Cutting a piece of wood into two |
c)
Figure 1 shows the front view and plan of a square pyramid.
Draw full size of the following views:
i)
front view
ii)
plan
a)
i)
Make a freehand pictorial sketch of the claw hammer.
ii)
Label any two parts of the claw hammer sketched in question (a)(i).
iii)
State one use of the claw hammer.
b)
Copy and complete the table below:
| S/N | PRODUCT | ONE SPECIFIC MATERIAL FOR MAKING THE PRODUCT |
| I | Body of sewing machine | |
| II | Water hose | |
| III | Gauge box | |
| IV | Traditional oven | |
| V | Drawing board |
c)
Figure 2 shows the pictorial sketch of a cassava grater made from sheet metal.
Re-arrange the following procedure for making the grater in the correct order.
i)
cut out the shape with snips;
ii)
draw patterns on paper;
iii)
punch holes on the sheet metal;
iv)
solder closed edges;
v)
fold workpiece.
d)
i)
Explain the term batching in blockwork.
ii)
Name one tool used for mixing mortar.
a)
i)
Make a freehand pictorial sketch of a ball-pein hammer.
ii)
Label any two parts of the ball-pein hammer sketched in question (a)(i).
iii)
State one use of the ball-pein hammer.
b)
Copy and complete the table below.
| S/N | MATERIAL | ONE USE | ONE PROPERTY |
| I | Mahogany | ||
| II | Nylon | ||
| III | Clay |
c)
i)
List two tools used for riveting metal pieces.
ii)
State two safety precautions to be observed when building a wall.
iii)
List two types of chisels used in wood work.
Digital Address: GZ-033-0057
King Kotey Road
Teshie - Accra
Ghana
+233 59 993 7122
Finland
+358 44 986 0934
info@kuulchat.com
© Copyright 2015 - 2024
All Rights Reserved
